Package bnxt_en kernel module for Broadcom NetXtreme-C/E based
Ethernet network chips like BCM573xx and BCM574xx.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is no file named busybox-1.36.1.tar.bz2 in the root directory of the website
The actual download link is “https://sources.buildroot.net/busybox/busybox-1.36.1.tar.bz2”
Signed-off-by: Jack Sun <sunjiazheng321521@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
i915 driver requires to load correct firmware to work on latest x86
GPU, it is more reasonable to make it as a kernel module, so that
initramfs is not required, and it can also save some space from the
kernel image comparing being a built-in driver
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
The broadcom PHY driver only has to depend upon PTP_1588_CLOCK_OPTIONAL
if NETWORK_PHY_TIMESTAMPING is enabled. The PTP functionality is stubbed
in this case.
Reflect this circumstance in the dependence condition. This allows to
build the driver as a built-in module even if PTP is built as a module.
This is required to include the broadcom PHY module regardless of the
built-setting of the PTP subsystem. On ath79 (and probably more)
targets with Broadcom PHY, Gigabit operation is currently broken as the
PHY driver is only built as a module in case all kernel-packages are
built. Due to this circumstance, affected devices fall back to using the
generic PHY driver.
Signed-off-by: David Bauer <mail@david-bauer.net>
This backport patch inserted suspend/resume callbacks
for the wrong PHY driver.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for FORESEE F35SQA001G SPI NAND.
Similar to F35SQA002G, but differs in capacity.
Datasheet:
- https://cdn.ozdisan.com/ETicaret_Dosya/704795_871495.pdf
Tested on Xiaomi AX3000T flashed with OpenWRT.
Signed-off-by: Bohdan Chubuk <chbgdn@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps WAN, 1x10/100/1000 Mbps LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: internal test points, 115200 8n1
- Power: 5 VDC, 3 A
Installation:
The installation must be done via TFTP by disassembling the router.
On other occasions Cudy has distributed intermediate firmware to make
installation easier, and so I recommend checking the Wiki for this
device if there is a more convenient solution than the one below.
To install using TFTP:
1. Connect to UART.
2. With the router off, press the RESET button. While the router is turning
on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a
TFTP server and an OpenWrt initramfs-kernel.bin firmware file.
5. Run these steps in u-boot using the name of your file.
setenv bootfile initramfs-kernel.bin
tftpboot
bootm
6. If you can reach LuCI or SSH now, just use the sysupgrade image
with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
